View By Date

Statistics

  • 254467
    Blogs
  • 54764
    Active Bloggers
8527 blogs
  • 03 Dec 2014
      Basic setting method and steps① Turn on ignition switch and not start engine.(Take Santana 3000 as an example to illustrate matching process)②Connect F3-D truck scanner (use OBD-II connector), select and click VW Audi, the screen will display as below: Pls select Version V7.2 V7.0 ③ Click V7.2(note: high version of software fully compatible to low version of software, if software version not high enough, pls upgrade timely),the screen shows as below Pls select version V7.2 V7.0 Openning. . .   ④ After open V7.2,the screen shows as below: VW Audi diagnostic system VW Audi diagnostic system   ⑤ Click VW Audi system, the screen will show as below: VW Audi diagnostic system General system Power system Chassis Comfort system Electronic system Function scanning Address code direct access ⑥ Click General system, the screen will show as below: General system 01- Engine 02- Automatic transmission 03- ABS 08- Air conditioning 09- Central electric control system 15- Airbag 16- Electronic steering wheel 17- Combination instrument panel (anti-theft) 18- Additional/auxiliary heating system 19- Gateway 22- 4-wheel drive ⑦ Click 01-engine,then screen will show as below: Audi KWP system function 01- Read vehicle computer model Read DTC Clear DTC 03- Component control test Read Data Stream 04- Basic setting 07- Controller coding 10- Adjust 11- Login Adaptive value clear ⑧ First read engine DTC, after confirming no DTC, click 04-basic setting and the screen will show as below:               ⑨After enter Channel No.060 in input box, click Confirm then screen shown below(Note: Item 4 shows Adaptive running means throttle and engine computer are matching, when it finished, it will shows Adaptive finished) After matching finished, press Back button to logout and then turn off ignition switch. Then turn on ignition switch and start engine to verify the matching effect. ⑩ If prompt error in the process of matching, mainly because of the following several reasons:  ●Channel No. input error, pls see the last content of this book to choose the appropriate channel No..     ●This vehicle without this function: If match SANTANA Gli, this vehicle originally cannot be matched with scanner  ●Throttle control unit or wire damage  ●Engine at running state, pls flameout, turn on ignition swtich  ●Throttle not reach idle stop(Carbon deposit or throttle cable adjustment improper)  ●Battery voltage too low;  ●Throttle control unit or wire damage;  ●Throttle stuck;  ●Starting engine or step on accelerator pedal during adaptive.  A⑾ After matching interruption, fault”17967”or “17973”will be saved in fault memory. Next time when turn on ignition switch, it will automatically perform basic setting.For Example: Throttle basic setting of Jetta CiX(duel valve) A⑿ ACommon VW throttle matching channel No.001Small Red Flag 488,Passat B4,Audi(100,200,V6 etc. old models)098Santana Gsi ,Passat B5(1.8),Jetta(5 valve),Audi(A6,V6)060 Jetta CiX(2 valve), A6(1.8,1.8T,2.4,2.8),Passat B5(1.8T,2.8),BORA, POLO Notes: After cleaning, adjusting and replacing throttle body; to realize kickdown function of automatic transmission, you need to perform engine computer matching as well as automatic transmission matching; Matching method as below: Connect to Fcar F3 1. Connect with Fcar 2. Turn on ignition switch, select “02 automatic transmission” 3. Read and clear DTC, and ensure no DTC saved in control unit; 4. Don’t touch engine accelerator pedal; 5. Select"04 basic setting" 6. Input channel No. "000" to confirm; 7. Step on accelerator pedal to floor and keep 3 seconds; 8. Logout, and release accelerator pedal. Note: For some new VW/Audi vehicles, the channel cannot be used when enter into automatic transmission control system.  Here must perform adjustment setting in "01-engine control system ", its channel No. is"063". Adaptive of throttle and automatic transmission computer is maily the above 2 methods.
    336 Posted by www.fcar.com
  •   Basic setting method and steps① Turn on ignition switch and not start engine.(Take Santana 3000 as an example to illustrate matching process)②Connect F3-D truck scanner (use OBD-II connector), select and click VW Audi, the screen will display as below: Pls select Version V7.2 V7.0 ③ Click V7.2(note: high version of software fully compatible to low version of software, if software version not high enough, pls upgrade timely),the screen shows as below Pls select version V7.2 V7.0 Openning. . .   ④ After open V7.2,the screen shows as below: VW Audi diagnostic system VW Audi diagnostic system   ⑤ Click VW Audi system, the screen will show as below: VW Audi diagnostic system General system Power system Chassis Comfort system Electronic system Function scanning Address code direct access ⑥ Click General system, the screen will show as below: General system 01- Engine 02- Automatic transmission 03- ABS 08- Air conditioning 09- Central electric control system 15- Airbag 16- Electronic steering wheel 17- Combination instrument panel (anti-theft) 18- Additional/auxiliary heating system 19- Gateway 22- 4-wheel drive ⑦ Click 01-engine,then screen will show as below: Audi KWP system function 01- Read vehicle computer model Read DTC Clear DTC 03- Component control test Read Data Stream 04- Basic setting 07- Controller coding 10- Adjust 11- Login Adaptive value clear ⑧ First read engine DTC, after confirming no DTC, click 04-basic setting and the screen will show as below:               ⑨After enter Channel No.060 in input box, click Confirm then screen shown below(Note: Item 4 shows Adaptive running means throttle and engine computer are matching, when it finished, it will shows Adaptive finished) After matching finished, press Back button to logout and then turn off ignition switch. Then turn on ignition switch and start engine to verify the matching effect. ⑩ If prompt error in the process of matching, mainly because of the following several reasons:  ●Channel No. input error, pls see the last content of this book to choose the appropriate channel No..     ●This vehicle without this function: If match SANTANA Gli, this vehicle originally cannot be matched with scanner  ●Throttle control unit or wire damage  ●Engine at running state, pls flameout, turn on ignition swtich  ●Throttle not reach idle stop(Carbon deposit or throttle cable adjustment improper)  ●Battery voltage too low;  ●Throttle control unit or wire damage;  ●Throttle stuck;  ●Starting engine or step on accelerator pedal during adaptive.  A⑾ After matching interruption, fault”17967”or “17973”will be saved in fault memory. Next time when turn on ignition switch, it will automatically perform basic setting.For Example: Throttle basic setting of Jetta CiX(duel valve) A⑿ ACommon VW throttle matching channel No.001Small Red Flag 488,Passat B4,Audi(100,200,V6 etc. old models)098Santana Gsi ,Passat B5(1.8),Jetta(5 valve),Audi(A6,V6)060 Jetta CiX(2 valve), A6(1.8,1.8T,2.4,2.8),Passat B5(1.8T,2.8),BORA, POLO Notes: After cleaning, adjusting and replacing throttle body; to realize kickdown function of automatic transmission, you need to perform engine computer matching as well as automatic transmission matching; Matching method as below: Connect to Fcar F3 1. Connect with Fcar 2. Turn on ignition switch, select “02 automatic transmission” 3. Read and clear DTC, and ensure no DTC saved in control unit; 4. Don’t touch engine accelerator pedal; 5. Select"04 basic setting" 6. Input channel No. "000" to confirm; 7. Step on accelerator pedal to floor and keep 3 seconds; 8. Logout, and release accelerator pedal. Note: For some new VW/Audi vehicles, the channel cannot be used when enter into automatic transmission control system.  Here must perform adjustment setting in "01-engine control system ", its channel No. is"063". Adaptive of throttle and automatic transmission computer is maily the above 2 methods.
    Dec 03, 2014 336
  • 21 Nov 2014
    Ketika rekomendasi cloud dedicated server muda dan terutama tato merayakan berhala dan sebagainya, menyenangkan klip ini hanya begitu baik Rekomendasi untuk Cloud Dedicated Server Terbaik dan Termurah di Indonesia ; =) Dan apa yang kita pelajari dari hal ini? Nah, berhati-hatilah dengan apa yang Anda tato. Rekomendasi untuk Cloud Dedicated Server Terbaik dan Termurah di Indonesia punya waktu terjemahan: Pia telah benar-benar berhati-hati untuk memilih tato bahwa dia tahu jauh di dalam hatinya dia masih akan menghargai ketika ia mencapai usia 70 tahun. Bernyanyi di depan orkestra simfoni besar besar di Stockholm dan bagaimana saya lama untuk minggu depan dan konser keberadaan saya akan melakukannya lagi. Perasaan "kagum" berdiri di depan semua musisi ini menakjubkan dan paduan suara Injil, alat bantu dengar mereka memainkan lagu-lagu di sebuah interpretasi yang indah dan saya pikir kinerja ini begitu menakjubkan ketika Anda mendengar mereka bermain dua lagu dan saya juga tahu mereka pikir itu sangat menyenangkan Rekomendasi untuk Cloud Dedicated Server Terbaik dan Termurah di Indonesia! Dan begitu juga Rekomendasi untuk Cloud Dedicated Server Terbaik dan Termurah di Indonesia. Rekomendasi untuk Cloud Dedicated Server Terbaik dan Termurah di Indonesia ketika saya masih jauh lebih muda, aku adalah penyanyi di Big Band dan itu juga sangat menyenangkan! Musik dengan alat nyata, bermain tanpa backing track dan melakukan "nyata" hal hidup, hanya begitu langka dan karena itu istimewa hari ini; =)
    282 Posted by Van Veen
  • Ketika rekomendasi cloud dedicated server muda dan terutama tato merayakan berhala dan sebagainya, menyenangkan klip ini hanya begitu baik Rekomendasi untuk Cloud Dedicated Server Terbaik dan Termurah di Indonesia ; =) Dan apa yang kita pelajari dari hal ini? Nah, berhati-hatilah dengan apa yang Anda tato. Rekomendasi untuk Cloud Dedicated Server Terbaik dan Termurah di Indonesia punya waktu terjemahan: Pia telah benar-benar berhati-hati untuk memilih tato bahwa dia tahu jauh di dalam hatinya dia masih akan menghargai ketika ia mencapai usia 70 tahun. Bernyanyi di depan orkestra simfoni besar besar di Stockholm dan bagaimana saya lama untuk minggu depan dan konser keberadaan saya akan melakukannya lagi. Perasaan "kagum" berdiri di depan semua musisi ini menakjubkan dan paduan suara Injil, alat bantu dengar mereka memainkan lagu-lagu di sebuah interpretasi yang indah dan saya pikir kinerja ini begitu menakjubkan ketika Anda mendengar mereka bermain dua lagu dan saya juga tahu mereka pikir itu sangat menyenangkan Rekomendasi untuk Cloud Dedicated Server Terbaik dan Termurah di Indonesia! Dan begitu juga Rekomendasi untuk Cloud Dedicated Server Terbaik dan Termurah di Indonesia. Rekomendasi untuk Cloud Dedicated Server Terbaik dan Termurah di Indonesia ketika saya masih jauh lebih muda, aku adalah penyanyi di Big Band dan itu juga sangat menyenangkan! Musik dengan alat nyata, bermain tanpa backing track dan melakukan "nyata" hal hidup, hanya begitu langka dan karena itu istimewa hari ini; =)
    Nov 21, 2014 282
  • 18 Nov 2014
    VW Throttle Matching:www.fcar.com Instruction: Throttle adjustment matching applies to VW vehicles with electronic throttle and without electronic throttle engine system. Santana GLi not in matching range. 1) Basic setting content: when turn on ignition switch; you can carry out adaptive of throttle control unit and engine control unit 2) In the following cases, adaptive must be performed:      ●Power supply interruption      ●Dismounting throttle control unit   ●Replace throttle control unit   ●Replace engine   ●Replace engine control unit 3) Conditions for Basic setting  ● No fault in fault memory  ● 11.5V Battery voltage no less than 11.5V  ● Close all accessories    ●Throttle should be in idle position    ●Engine coolant temperature greater than 85 ℃ 4)Basic setting method and steps ① Turn on ignition switch and not start engine.(Take Santana 3000 as an example to illustrate matching process) ②Connect F3-D scanner (use OBD-II connector), select and click VW Audi, the screen will display as below: Pls select Version V7.2 V7.0 ③ Click V7.2(note: high version of software fully compatible to low version of software, if software version not high enough, pls upgrade timely),the screen shows as below Pls select version V7.2 V7.0 Openning. . . ④ After open V7.2,the screen shows as below: VW Audi diagnostic system VW Audi diagnostic system ⑤ Click VW Audi system, the screen will show as below: VW Audi diagnostic system General system Power system Chassis Comfort system Electronic system Function scanning Address code direct access ⑥ Click General system, the screen will show as below: General system 01- Engine 02- Automatic transmission 03- ABS 08- Air conditioning 09- Central electric control system 15- Airbag 16- Electronic steering wheel 17- Combination instrument panel (anti-theft) 18- Additional/auxiliary heating system 19- Gateway 22- 4-wheel drive ⑦ Click 01-engine,then screen will show as below: Audi KWP system function 01- Read vehicle computer model Read DTC Clear DTC 03- Component control test Read Data Stream 04- Basic setting 07- Controller coding 10- Adjust 11- Login Adaptive value clear ⑧ First read engine DTC, after confirming no DTC, click 04-basic setting and the screen will show as below:              ⑨After enter Channel No.060 in input box, click Confirm then screen shown below(Note: Item 4 shows Adaptive running means throttle and engine computer are matching, when it finished, it will shows Adaptive finished) After matching finished, press Back button to logout and then turn off ignition switch. Then turn on ignition switch and start engine to verify the matching effect. ⑩ If prompt error in the process of matching, mainly because of the following several reasons:  ●Channel No. input error, pls see the last content of this book to choose the appropriate channel No..     ●This vehicle without this function: If match SANTANA Gli, this vehicle originally cannot be matched with scanner  ●Throttle control unit or wire damage  ●Engine at running state, pls flameout, turn on ignition swtich  ●Throttle not reach idle stop(Carbon deposit or throttle cable adjustment improper)  ●Battery voltage too low;  ●Throttle control unit or wire damage;  ●Throttle stuck;  ●Starting engine or step on accelerator pedal during adaptive.  A⑾ After matching interruption, fault”17967”or “17973”will be saved in fault memory. Next time when turn on ignition switch, it will automatically perform basic setting. For Example: Throttle basic setting of Jetta CiX(duel valve) A⑿ ACommon VW throttle matching channel No. 001 Small Red Flag 488,Passat B4,Audi(100,200,V6 etc. old models) 098 Santana Gsi ,Passat B5(1.8),Jetta(5 valve),Audi(A6,V6) 060 Jetta CiX(2 valve), A6(1.8,1.8T,2.4,2.8),Passat B5(1.8T,2.8),BORA, POLO Notes: After cleaning, adjusting and replacing throttle body; to realize kickdown function of automatic transmission, you need to perform engine computer matching as well as automatic transmission matching; Matching method as below: Connect to Fcar F3 1. Connect with Fcar 2. Turn on ignition switch, select “02 automatic transmission” 3. Read and clear DTC, and ensure no DTC saved in control unit; 4. Don’t touch engine accelerator pedal; 5. Select"04 basic setting" 6. Input channel No. "000" to confirm; 7. Step on accelerator pedal to floor and keep 3 seconds; 8. Logout, and release accelerator pedal. Note: For some new VW/Audi vehicles, the channel cannot be used when enter into automatic transmission control system. Here must perform adjustment setting in "01-engine control system ", its channel No. is"063". Adaptive of throttle and automatic transmission computer is maily the above 2 methods.
    344 Posted by www.fcar.com
  • VW Throttle Matching:www.fcar.com Instruction: Throttle adjustment matching applies to VW vehicles with electronic throttle and without electronic throttle engine system. Santana GLi not in matching range. 1) Basic setting content: when turn on ignition switch; you can carry out adaptive of throttle control unit and engine control unit 2) In the following cases, adaptive must be performed:      ●Power supply interruption      ●Dismounting throttle control unit   ●Replace throttle control unit   ●Replace engine   ●Replace engine control unit 3) Conditions for Basic setting  ● No fault in fault memory  ● 11.5V Battery voltage no less than 11.5V  ● Close all accessories    ●Throttle should be in idle position    ●Engine coolant temperature greater than 85 ℃ 4)Basic setting method and steps ① Turn on ignition switch and not start engine.(Take Santana 3000 as an example to illustrate matching process) ②Connect F3-D scanner (use OBD-II connector), select and click VW Audi, the screen will display as below: Pls select Version V7.2 V7.0 ③ Click V7.2(note: high version of software fully compatible to low version of software, if software version not high enough, pls upgrade timely),the screen shows as below Pls select version V7.2 V7.0 Openning. . . ④ After open V7.2,the screen shows as below: VW Audi diagnostic system VW Audi diagnostic system ⑤ Click VW Audi system, the screen will show as below: VW Audi diagnostic system General system Power system Chassis Comfort system Electronic system Function scanning Address code direct access ⑥ Click General system, the screen will show as below: General system 01- Engine 02- Automatic transmission 03- ABS 08- Air conditioning 09- Central electric control system 15- Airbag 16- Electronic steering wheel 17- Combination instrument panel (anti-theft) 18- Additional/auxiliary heating system 19- Gateway 22- 4-wheel drive ⑦ Click 01-engine,then screen will show as below: Audi KWP system function 01- Read vehicle computer model Read DTC Clear DTC 03- Component control test Read Data Stream 04- Basic setting 07- Controller coding 10- Adjust 11- Login Adaptive value clear ⑧ First read engine DTC, after confirming no DTC, click 04-basic setting and the screen will show as below:              ⑨After enter Channel No.060 in input box, click Confirm then screen shown below(Note: Item 4 shows Adaptive running means throttle and engine computer are matching, when it finished, it will shows Adaptive finished) After matching finished, press Back button to logout and then turn off ignition switch. Then turn on ignition switch and start engine to verify the matching effect. ⑩ If prompt error in the process of matching, mainly because of the following several reasons:  ●Channel No. input error, pls see the last content of this book to choose the appropriate channel No..     ●This vehicle without this function: If match SANTANA Gli, this vehicle originally cannot be matched with scanner  ●Throttle control unit or wire damage  ●Engine at running state, pls flameout, turn on ignition swtich  ●Throttle not reach idle stop(Carbon deposit or throttle cable adjustment improper)  ●Battery voltage too low;  ●Throttle control unit or wire damage;  ●Throttle stuck;  ●Starting engine or step on accelerator pedal during adaptive.  A⑾ After matching interruption, fault”17967”or “17973”will be saved in fault memory. Next time when turn on ignition switch, it will automatically perform basic setting. For Example: Throttle basic setting of Jetta CiX(duel valve) A⑿ ACommon VW throttle matching channel No. 001 Small Red Flag 488,Passat B4,Audi(100,200,V6 etc. old models) 098 Santana Gsi ,Passat B5(1.8),Jetta(5 valve),Audi(A6,V6) 060 Jetta CiX(2 valve), A6(1.8,1.8T,2.4,2.8),Passat B5(1.8T,2.8),BORA, POLO Notes: After cleaning, adjusting and replacing throttle body; to realize kickdown function of automatic transmission, you need to perform engine computer matching as well as automatic transmission matching; Matching method as below: Connect to Fcar F3 1. Connect with Fcar 2. Turn on ignition switch, select “02 automatic transmission” 3. Read and clear DTC, and ensure no DTC saved in control unit; 4. Don’t touch engine accelerator pedal; 5. Select"04 basic setting" 6. Input channel No. "000" to confirm; 7. Step on accelerator pedal to floor and keep 3 seconds; 8. Logout, and release accelerator pedal. Note: For some new VW/Audi vehicles, the channel cannot be used when enter into automatic transmission control system. Here must perform adjustment setting in "01-engine control system ", its channel No. is"063". Adaptive of throttle and automatic transmission computer is maily the above 2 methods.
    Nov 18, 2014 344
  • 30 Oct 2014
    Packers and Movers in Chandigarh   Packers along with movers Bangalore targeted companies are commonly often competent at cope with by way of the actual satisfying coordination. Most of these government bodies overall the actual change reasonable guaranteeing persons are able to get go easy around the brand-new location. Most of these government bodies create the actual persons far from a lot of difficulties. Movers along with packers Bangalore targeted corporations achieve spot to location you will want to windup the actual change successfully. They are able to payment cost-effective importance designed for making the actual move ahead straightforward. And so simply get the real firms around the exclusive useful corporations designed for making the actual move ahead trustworthy along with risk-free. Fully gratifying so that you can Packers Movers Bangalore. We've been one significant packer along with movers within Bangalore. We've been displaying these organizations not only within Bangalore together with exclusive major communities connected with Bangalore. We've been skilled to support people about center change in addition to about long-distance. We've been displaying superior exceptional along with in reality pro corporations simply by economy fantastic expenditures. Changing create people consider awful exhibited you get out there difficulties connected with duties. Those who don’t would like to services the actual perform connected with move ahead they have to maybe be talk with the actual identified transporting over corporations. You could learn quantity of corporations affecting economy that really assist the actual clientele far from a lot of concerns. Most of these government bodies services the overall culpability on the run working together with persons. They are able to manage all of your recent measures to the sum until in the long run these sorts of change instantly obtain easy. Most of these corporations start using a foolproof approach even though seen just by they're going to overall the entire measures.   Packers and Movers Chandigarh   Resource: http://3th.co.in/packers-and-movers-chandigarh/
    194 Posted by shashi
  • shashiBy shashi
    Packers and Movers in Chandigarh   Packers along with movers Bangalore targeted companies are commonly often competent at cope with by way of the actual satisfying coordination. Most of these government bodies overall the actual change reasonable guaranteeing persons are able to get go easy around the brand-new location. Most of these government bodies create the actual persons far from a lot of difficulties. Movers along with packers Bangalore targeted corporations achieve spot to location you will want to windup the actual change successfully. They are able to payment cost-effective importance designed for making the actual move ahead straightforward. And so simply get the real firms around the exclusive useful corporations designed for making the actual move ahead trustworthy along with risk-free. Fully gratifying so that you can Packers Movers Bangalore. We've been one significant packer along with movers within Bangalore. We've been displaying these organizations not only within Bangalore together with exclusive major communities connected with Bangalore. We've been skilled to support people about center change in addition to about long-distance. We've been displaying superior exceptional along with in reality pro corporations simply by economy fantastic expenditures. Changing create people consider awful exhibited you get out there difficulties connected with duties. Those who don’t would like to services the actual perform connected with move ahead they have to maybe be talk with the actual identified transporting over corporations. You could learn quantity of corporations affecting economy that really assist the actual clientele far from a lot of concerns. Most of these government bodies services the overall culpability on the run working together with persons. They are able to manage all of your recent measures to the sum until in the long run these sorts of change instantly obtain easy. Most of these corporations start using a foolproof approach even though seen just by they're going to overall the entire measures.   Packers and Movers Chandigarh   Resource: http://3th.co.in/packers-and-movers-chandigarh/
    Oct 30, 2014 194
  • 22 Oct 2014
    Public data line is used for connection to F3-D truck scanner, Data line is used for communication with ECU as well as information communication with other vehicle electronic devices, such as electronic instrument panel and other devices. Some engines have two public data lines: one is in the whole wiring harness (engine side data line); another is separated from ECU harness, normally locate in cab. Pic.4-33 shows the data lines of early electronically controlled engine. They all have a rectangular 12-pin connector. There are 3 kinds of special harness that used for different type of diagnostic data connector, when troubleshooting, maintenance technician connect appropriate diagnostic plug to diagnostic data connector, and then can download fault code saved in ECU memory. New type of electronically controlled engines all adopt standard SAE data line as shown in Pic.4-34(b).The connection of 6-pin connector is as below, when detect communication failure between pin and truck diagnostic tool, you can measure voltage of this pin with digimer.                                  Pic.4-33 (a). Used for connection with engine, vehicle diagnostic socket and Fcar F3-D truck diagnostic tool, 6-pin socket and 9-pin socket.                               Pic.4-34 (b).Standard SAE 6-pin German-made connector A——data line(十);voltage normally between 2.5~5V. B——data line(—);voltage normally between 0~2.5V. C——Battery(12V or 24V);12V  Electric System are different from 24V Electric System, normally between 10~27V. D——open circuit;voltage normally between 4~5V E——Cylinder body ground;0V F——Unused. F3-D heavy truck diagnostic scanner can diagnose all kinds of diesel control systems quickly and easily, especially available for China, Europe, America, Japan and Korea and so on,build-in high/low speed CAN-Bus to satisfy all Can-Bus vehicles; Coverage: MAN, Mitsubishi Fuso, Scania, ISUZU,  MACK, HINO, VOLOV, DAF, Astra, Detroit, BENZ, NISSAN UD, Catepillar, Renault,...and most of CHINA Heavy duty trucks , BUS......... Bosch, Cummins, Catepillar, Denso, Siemens, Motorola, Zexel, VITO, NanYue, Delphi, Wabco……
    285 Posted by www.fcar.com
  • Public data line is used for connection to F3-D truck scanner, Data line is used for communication with ECU as well as information communication with other vehicle electronic devices, such as electronic instrument panel and other devices. Some engines have two public data lines: one is in the whole wiring harness (engine side data line); another is separated from ECU harness, normally locate in cab. Pic.4-33 shows the data lines of early electronically controlled engine. They all have a rectangular 12-pin connector. There are 3 kinds of special harness that used for different type of diagnostic data connector, when troubleshooting, maintenance technician connect appropriate diagnostic plug to diagnostic data connector, and then can download fault code saved in ECU memory. New type of electronically controlled engines all adopt standard SAE data line as shown in Pic.4-34(b).The connection of 6-pin connector is as below, when detect communication failure between pin and truck diagnostic tool, you can measure voltage of this pin with digimer.                                  Pic.4-33 (a). Used for connection with engine, vehicle diagnostic socket and Fcar F3-D truck diagnostic tool, 6-pin socket and 9-pin socket.                               Pic.4-34 (b).Standard SAE 6-pin German-made connector A——data line(十);voltage normally between 2.5~5V. B——data line(—);voltage normally between 0~2.5V. C——Battery(12V or 24V);12V  Electric System are different from 24V Electric System, normally between 10~27V. D——open circuit;voltage normally between 4~5V E——Cylinder body ground;0V F——Unused. F3-D heavy truck diagnostic scanner can diagnose all kinds of diesel control systems quickly and easily, especially available for China, Europe, America, Japan and Korea and so on,build-in high/low speed CAN-Bus to satisfy all Can-Bus vehicles; Coverage: MAN, Mitsubishi Fuso, Scania, ISUZU,  MACK, HINO, VOLOV, DAF, Astra, Detroit, BENZ, NISSAN UD, Catepillar, Renault,...and most of CHINA Heavy duty trucks , BUS......... Bosch, Cummins, Catepillar, Denso, Siemens, Motorola, Zexel, VITO, NanYue, Delphi, Wabco……
    Oct 22, 2014 285
  • 10 Oct 2014
    1#:K line; 2#:K line; 3#:K line; GND:Ground wire(negative); 6#:CAN‐H; 7#:RSR232+, J1708+, K line;8#:K line; 9#:K line; 10#:K line; 11#:K line; 12#:K line; 13#:K line; 14#:CAN‐L; 15#:RSR232‐, K line, J1708‐, L line VCC: power line(Positive); POWER:Power indicator. Remark: If lack of vehicle electrical equipment knowledge or unable to confirm electrical equipment power supply, please don’t operate jumper, for error operation of jumper may lead to malfunction of electrical failure or FCAR F3-D main unit and wire.                                                            Pic. 4‐39    (Auto diagnostic socket related information reconfirmed as below) ● Digital high impedance multimeter (can not use Analog Multimeter) ● When ignition switch to ON Gear, there is supply voltage of vehicle on diagnostic socket. Voltage difference between voltage on diagnostic socket and vehicle battery side can not be above 2.5V.  In diagnosis, if the signal line used is single-line communication (K line), voltage on signal line lower than battery voltage,(if vehicle supply voltage is 12V,then voltage on signal line is 11V, + 0.25V;if 24V,signal voltage is 21V,+ 0.25V) If double signal line adopts CAN communication, 2 diagnostic lines use multimeter to measure ground wire voltage under the condition that ignition switch open, the sum of both voltages is 5V,average 2.5V,the one voltage little higher than 2.5V is CAN-H, the one voltage lower than 2.5V is CAN-L.   After understanding of the above, then you can use auto scanner to read DTC. Now make a brief introduction of operation steps for FCAR scanner to read DTC: Confirm diagnostic socket connect properly and then turn on power switch of scanner, and select Diagnostic menu (As shown in Pic.4-39).    11、Select vehicle type to be diagnosed: ●Diesel ●Machine   Select vehicle type and then enter into vehicle series or engine select menu (as shown in 4‐40):Then enter into engine type or electronically controlled system menu (As show in Pic. 4‐41) After entry to engine type or electronically controlled system menu, it will shows function menu of scanner (As show in Pic. 4‐42)                                           Pic.4-40 model or engine menu                                                                   Pic.4-41 ECU menu    If need to clear DTC saved in ECU memory, then must select “Clear DTC” menu option. At present, all Electronic Control Systems are required to use this method. Some first generation of Electronic Control System can clear saved DTCs by way of using scanner or dismantling ECU power fuse for 10s and then install. The shortcoming of this kind of system is all DTCs appeared and recorded in the process of driving will disappear once driver cleared DTCs, therefore maintenance technician and fleet maintenance manager would know nothing about the problem of engine and vehicles. Note: Before clearing DTC, better write down DTCs, also can use printing function of Fcar scanner. Pic.4‐42 Function select menu
    417 Posted by www.fcar.com
  • 1#:K line; 2#:K line; 3#:K line; GND:Ground wire(negative); 6#:CAN‐H; 7#:RSR232+, J1708+, K line;8#:K line; 9#:K line; 10#:K line; 11#:K line; 12#:K line; 13#:K line; 14#:CAN‐L; 15#:RSR232‐, K line, J1708‐, L line VCC: power line(Positive); POWER:Power indicator. Remark: If lack of vehicle electrical equipment knowledge or unable to confirm electrical equipment power supply, please don’t operate jumper, for error operation of jumper may lead to malfunction of electrical failure or FCAR F3-D main unit and wire.                                                            Pic. 4‐39    (Auto diagnostic socket related information reconfirmed as below) ● Digital high impedance multimeter (can not use Analog Multimeter) ● When ignition switch to ON Gear, there is supply voltage of vehicle on diagnostic socket. Voltage difference between voltage on diagnostic socket and vehicle battery side can not be above 2.5V.  In diagnosis, if the signal line used is single-line communication (K line), voltage on signal line lower than battery voltage,(if vehicle supply voltage is 12V,then voltage on signal line is 11V, + 0.25V;if 24V,signal voltage is 21V,+ 0.25V) If double signal line adopts CAN communication, 2 diagnostic lines use multimeter to measure ground wire voltage under the condition that ignition switch open, the sum of both voltages is 5V,average 2.5V,the one voltage little higher than 2.5V is CAN-H, the one voltage lower than 2.5V is CAN-L.   After understanding of the above, then you can use auto scanner to read DTC. Now make a brief introduction of operation steps for FCAR scanner to read DTC: Confirm diagnostic socket connect properly and then turn on power switch of scanner, and select Diagnostic menu (As shown in Pic.4-39).    11、Select vehicle type to be diagnosed: ●Diesel ●Machine   Select vehicle type and then enter into vehicle series or engine select menu (as shown in 4‐40):Then enter into engine type or electronically controlled system menu (As show in Pic. 4‐41) After entry to engine type or electronically controlled system menu, it will shows function menu of scanner (As show in Pic. 4‐42)                                           Pic.4-40 model or engine menu                                                                   Pic.4-41 ECU menu    If need to clear DTC saved in ECU memory, then must select “Clear DTC” menu option. At present, all Electronic Control Systems are required to use this method. Some first generation of Electronic Control System can clear saved DTCs by way of using scanner or dismantling ECU power fuse for 10s and then install. The shortcoming of this kind of system is all DTCs appeared and recorded in the process of driving will disappear once driver cleared DTCs, therefore maintenance technician and fleet maintenance manager would know nothing about the problem of engine and vehicles. Note: Before clearing DTC, better write down DTCs, also can use printing function of Fcar scanner. Pic.4‐42 Function select menu
    Oct 10, 2014 417
  • 09 Oct 2014
    ​You can open the ECU reader Trouble diagnosis menu in the system main interface and select【Chinese Series】 Note : Here take【Engine system】as an exampleEntering 【Chinese series】Menu and select the logo of 【Engine system】Click【Engine system】logo, the ECU reader screen will display the prompt.Note: Select the version you need or the highest version to test or diagnose, the highest version of all software is fully compatible to the existing version.After selecting version, the check engine code reader screen will display the【Engine】engine electronic control system list toNote: The fault diagnosis can also be conducted in the ECU of same assembling and different model. But data stream, trouble code etc will be not accurate or information can’t be displayed. Thus the fault diagnostic computer menu should choose the diagnostic program that matched with the ECU model of body assembling to diagnose.There are more engine control systems assembled in domestic vehicles. Maintenance technicians can obtain diagnostic procedure menu of ECU mode from the electronic control system ECU's nameplate. ​http://www.fcar.com/auto-diagnostic-scanner/4-f3-d-heavy-duty.html
    312 Posted by www.fcar.com
  • ​You can open the ECU reader Trouble diagnosis menu in the system main interface and select【Chinese Series】 Note : Here take【Engine system】as an exampleEntering 【Chinese series】Menu and select the logo of 【Engine system】Click【Engine system】logo, the ECU reader screen will display the prompt.Note: Select the version you need or the highest version to test or diagnose, the highest version of all software is fully compatible to the existing version.After selecting version, the check engine code reader screen will display the【Engine】engine electronic control system list toNote: The fault diagnosis can also be conducted in the ECU of same assembling and different model. But data stream, trouble code etc will be not accurate or information can’t be displayed. Thus the fault diagnostic computer menu should choose the diagnostic program that matched with the ECU model of body assembling to diagnose.There are more engine control systems assembled in domestic vehicles. Maintenance technicians can obtain diagnostic procedure menu of ECU mode from the electronic control system ECU's nameplate. ​http://www.fcar.com/auto-diagnostic-scanner/4-f3-d-heavy-duty.html
    Oct 09, 2014 312